LT4256-1/LT4256-2
11
425612fa
APPLICATIO S I FOR ATIO
U
U
U
When the TIMER pin reaches 4.65V (typ), the internal fault
latch is set causing GATE to be pulled low and TIMER to be
discharged to GND by the 3礎 current source. The part is
not allowed to turn on again until the voltage on TIMER
falls below 0.65V (typ).
TIMER must never be pulled high by a low impedance
because whenever TIMER rises above the upper threshold
(typically 4.65V) the pin characteristics change from a
high impedance current source to a low impedance.
Whenever GATE is commanded off by any fault condition,
it is discharged rapidly, turning off the external MOSFET.
The waveform in Figure 9 shows how the output latches off
following a current fault (LT4256-1). The drop across the
sense resistor is held at 55mV as the timer ramps up. Once
TIMER reaches its shutdown threshold (4.65V typically),
the circuit latches off.
The LT4256-1 latches off after a current limit fault. After
the LT4256-1 latches off, the part may be commanded to
start back up. This is accomplished by cycling UV to
ground and then back high (this command can only be
accepted after TIMER discharges back below the 0.65V
typical threshold, to prevent overheating transistor Q1).
Automatic Restart
The LT4256-2 will automatically restart after an overcurrent
fault. These waveforms are shown in Figure 10.
The LT4256-2 functionality is as follows: When an
overcurrent condition occurs, the GATE pin is servoed to
maintain a constant voltage across the sense resistor, and
the capacitor C2 at the TIMER pin will begin to charge.
When the voltage at the TIMER pin reaches 4.65V (typ),
the GATE pin is pulled low. When the voltage at the TIMER
pin ramps back down to 0.65V (typ), the LT4256-2 turns
on again. If the short-circuit condition at the output still
exists, the cycle will repeat itself indefinitely. The duty
cycle under short-circuit conditions is 3% which prevents
Q1 from overheating.
Figure 9. LT4256-1 Current Limit Waveforms
Figure 10. LT4256-2 Current Limit Waveforms
10ms/DIV
4256 F09
I
OUT
500mA/DIV
V
OUT
50V/DIV
TIMER
5V/DIV
GATE
50V/DIV
I
OUT
500mA/DIV
V
OUT
50V/DIV
TIMER
5V/DIV
GATE
50V/DIV
10ms/DIV
4256 F10
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LTC1392IS8#TRPBF
IC DATA ACQ SYSTEM 10BIT 8-SOIC
LTC1421ISW-2.5#PBF
IC CONTROLLER HOT SWAP 24-SOIC
LTC1422CN8
IC CONTROLLER HOT SWAP 8-DIP
LTC1642CGN#TRPBF
IC CONTROLLER HOTSWAP ADJ 16SSOP
LTC1643AL-1CGN#PBF
IC CTRLR HOTSWAP PCI BUS 16SSOP
LTC1644CGN#TRPBF
IC CONTROLLER HOT SWAP 20-SSOP
LTC1645IS#TRPBF
IC CTRLR SEQ HOTSWAP DUAL 14SOIC
LTC1646IGN#TR
IC CNTRLR HOTSWAP PCIDUAL 16SSOP
相关代理商/技术参数
LT4256-2
制造商:LINER 制造商全称:Linear Technology 功能描述:Positive High Voltage Hot Swap Controllers
LT4256-2CS8
功能描述:IC CTRLR HOTSWAP HV AUTO 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LT4256-2CS8#PBF
功能描述:IC CTLR HOTSWAP HV AUTO 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LT4256-2CS8#PBF
制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER, 48V, SOIC-8
LT4256-2CS8#TR
功能描述:IC CTRLR HOTSWAP HV AUTO 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LT4256-2CS8#TRPBF
功能描述:IC CTRLR HOTSWAP HV AUTO 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LT4256-2IS8
功能描述:IC CTRLR HOTSWAP HV AUTO 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件
LT4256-2IS8#PBF
功能描述:IC CTLR HOTSWAP HV AUTO 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF)